notes: 1. all dimensions are in millimeters (inches). 2. tolerances are 0.1mm (0.004inch) unless otherwise noted. 3. polarity referring onto the cathode mark is reversed on the red. a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd . surface mount led lamps full color chip led lamps part number: AL-HUBG6B434T package outlines & re-flow profile ? soldering iron basic spec is u 5sec when 260 . if temperature is higher, time should be shorter (+10 ? -1sec ).power dissipation of iron should be smaller than 15w, and temperatures should be contro llable .surface temperature of the device should be under 230 . ? reflow temp/time item materials resin (mold) epoxy lens color water clear printed circuit board bt algainp ingan dice ingan brilliant red brilliant green emitted color blue for reflow soldering
a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd . surface mount led lamps part number: AL-HUBG6B434T electro-optical characteristics (t a =25 ) value parameter emitted color test condition symbol min. typ. max. unit r ? 2.0 2.4 g ? 3.2 3.6 forward voltage b i f =20ma v f ? 3.2 3.6 v r ? 90 ? g ? 180 ? luminous intensity b i f =20ma i v ? 50 ? mcd r 632 g 518 b p 468 r ? 624 ? g ? 525 ? wavelength b i f =20ma d ? 470 ? nm r 20 g 35 spectral line half-width b i f =20ma 35 nm r 60 g 100 peak pulsing current (1/10 duty f=1khz) b i f =20ma i fp 100 ma r 60 g 110 power dissipation b i f =20ma p d 110 mw absolute maximum ratings (t a =25 ) parameter symbol value unit viewing angle at 50% iv 2 1/2 100 deg forward current i f 25 ma reverse voltage v r 5 v reverse current i r 50 a operating temperature range top -40 ~+85 storage temperature range tstg -40 ~+90
a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd . surface mount led lamps part number: AL-HUBG6B434T test items and results of reliability refer to reliability test standard specification for in this line. no item test conditions test hours/cycle sample size ac/re 1 solder heat temp 2605 5 sec. 76 pcs 0/1 2 temperature cycle h +85 30min 5min l -55 30min 50 cycles 76 pcs 0/1 3 thermal shock h +100 5min 10set l -10 5min 50 cycles 76 pcs 0/1 4 high temperature storage temp 100 1000 hrs 76 pcs 0/1 5 low temperature storage temp -55 1000 hrs 76 pcs 0/1 6 dc operating life i f =20ma 1000 hrs 76 pcs 0/1 7 high temperature / high humidity 85 / 85%rh 1000 hrs 76 pcs 0/1
a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd. surface mount led lamps part number: AL-HUBG6B434T typical electro-optical characteristics curves
a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd. surface mount led lamps part number: AL-HUBG6B434T typical electro-optical characteristics curves
precautions for use 1. over-current proof customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (burn out will happen). 2. storage 2.1 do not open moisture proof bag befo re the products are ready to use. 2.2 before opening the package, the leds should be kept at 30 or less and 90%rh or less. 2.3 the leds should be used within a year. 2.4 after opening the package, the leds should be kept at 30 or less and 70%rh or less. 2.5 the leds should be used within 168 hour s (7 days) after opening the package. 2.6 if the moisture absorbent material (silica ge l) has faded away or the leds have exceeded the storage time, baking treatment should be performed using the following conditions. baking treatment U 60 5 for 24 hours. 3. soldering condition 3.1 pb-free solder temperature profile 3.2 reflow soldering should not be done more than two times. 3.3 when soldering, do not put stress on the leds during heating. 3.4 after soldering, do not warp the circuit board. 4. soldering iron each terminal is to go to the tip of soldering iron temper ature less than 280 for 3 seconds within once in less than soldering ir on capacity 25w. leave two seconds and more intervals, and do soldering of each terminal. be careful because the damage of the product is often started at the time of the hand solder. a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd. surface mount led lamps part number: al-hubg6b4343t
|
